基本信息：
Product Introduction:
JS聚合物水泥基防水涂料是由合成高分子聚合物乳液（如聚丙烯酸酯、聚醋酸乙烯酯、丁苯橡胶乳液）及各种添加剂优化组合而成的液料复合而成的单组分防水涂料，是一种既具有合成高分子聚合物材料弹性高、又有无机材料耐久性好的防水材料。
JS Polymer waterproof slurry is made from Synthesis of polymer emulsion(such as polyacrylate, polyvinyl acetate, styrene butadiene rubber emulsion)and various additives. Therefore, it is a waterproof material with high elasticity and good durability.
适用范围：
Scope of application
可在潮湿或干燥的砖石、砂浆、混凝土、金属、木材、硬塑料、玻璃、石膏板、泡沫板、橡胶、等基面上施工。对于新旧建筑物及构造物（例如：房屋、地下工程、隧道、桥梁、水池等）均可使用，同时也可做粘贴剂使用（欢迎免费注册，登陆中国涂料在线（涂料在线）行业门户网址www.coatingol.com，免费发布供求，免费发布产品，免费发布企业动态）。特别适合地下室、地下隧道、卫浴间、水池等，特别潮湿及长期在水中浸泡的条件下的施工。
It can be applied on the surface of wet or dry masonry, mortar, concrete, metal, wood, hard plastic, glass, gypsum board, foam board, rubber, and so on. Its applicable to houses, underground works, tunnels, bridges, pools, etc too. They can also be used as stickers, especially suitable for basement, underground tunnel, bathroom room, pool, etc., where the place is wet and immersed in water for a long time.
产品特性：
Features
1. 环保型产品、Ⅰ型耐紫外线，耐老化，特别适用于屋面防水工程；
Its a kind of environmental products. Type “I” has feature of UV resistance, aging resistance, especially suitable for roof waterproofing engineering.
2. 可作饮水工程，特别适用于长期进水的防水工程；
It can be used as drinking water engineering project, especially suitable for long-term influent waterproofing project.
3. 可在潮湿面上施工、工期短、操作方便；
It can be constructed on wet surface. It has feature of short construction period and convenient operation.
4. 涂层高弹、粘接力强、耐腐蚀；
Has high elasticity, strong adhesion and corrosion resistance.
5. 可锟、可刷、批刮、堵漏、修补。防水层具有整体无缝的特性；
Can be brushed, scraped, blocked and repaired. The waterproof layer is seamless as a whole.
6. 具有抗震性，可适应基层微小变形，能起到遮蔽裂纹和抑制表面产生裂纹的作用。
It ‘s seismic resistance, adapt to the small deformation of the base, and can cover the crack and inhibit the crack on the surface.
基面处理：
Base surface dispostion
1. 基面必须稳固、清洁、平整、无灰尘、无油污。假如有明显的空隙、砂眼需要用水泥砂浆堵塞、抹平，尖锐的边缘应除去。
The base surface must be stable, clean, flat, dust-free and oil-free. If there are obvious voids and sandholes, must block and smooth them using cement mortar. Sharp edges should be removed too.
2. 渗漏处须先进性堵漏处理，阴阳角应做成圆弧形。
The leakage place must be blocked in advance. The internal angle and external angle should be made into a circular arc.
施工说明：
Construction Guidance
首先，将添加剂倒进桶（或其他容器）内，用慢速电钻（约4000转/分）搅拌，同时慢慢加入配套的粉料，搅拌4-5分钟直至均匀，然后静至5分钟才可以使用。
如果基层过于干燥，先用水将基面稍微湿润（无明水为准）。对可能会产生裂缝的地方，要铺设胎体增强材料。配置好的涂料应在4小时内用完。
涂刷至少两遍，第二遍必须等到上次干固不粘手方可进行。两次涂刷需要交叉垂直，这样才能达到最好的覆盖效果。
First of all, pour the additive into the bucket (or other container), stir with a slow electric drill (about 4000 rpm / min), and slowly add the matching powder, stir for 4- 5 minutes until it become even, and then place it statically for 5 minutes before you use it.
If the base layer is too dry, moisturize the base a little but not make it to wet to see water. Reinforce it to where cracks may occur. The configured paint should be used up within 4 hours.
Brushing should be twice at least, the second time must wait until it become dry and not stick to the hand. Two brushes should be cross-vertically in order to achieve the best coverage effect
执行标准：
Execution Standards:
JSⅡ GB23445-2009《聚合物水泥防水涂料》
JSⅡ GB23445-2009《Polymer cement waterproof coating 》
保质日期和存储
Validity Period & Storage conditions
原装密封产品放于阴凉干燥处，有效期为一年。
Original sealed products should be placed in dry and cool places. The validity period is 12 months.